Categories
Concrete

How to adjust garage door tracks

How to adjust garage door tracks

Operating with a garage door that is out of alignment is a risk not worth taking. For starters, you might get locked in or out of your garage if the door is jammed tight. In worse cases, the out-of-balance door could snap from the tracks and injure persons standing nearby. Out of place garage doors are also a security risk. Since the door can’t lock correctly, it makes your whole house vulnerable to burglary. The only solution to all these risk scenarios would be to adjust the garage door tracks as soon as the problem arises. This article will go over how to adjust garage door tracks so that you can use a regularly operating garage door.

What Causes Misalignment in Garage Doors?

There could be many reasons why your garage doors tracks are out of place. The most common problem is old doors or worn out rubber moldings. It could be that the garage door has become loose due to regular use. No matter what the cause of the problem is, below is a step by step guide to get your garage door back on track.

Binding Garage Doors – Know How to Fix Any Issue

1. Loosen the Track Screws

A garage door is considered binding if it is hard to move up or down. The reason for that could be that the screws are too tight so your best move would be to loosen them. Open the garage to access the bolts on the track brackets. Loosen the bolts that secure the track brackets to the track brackets using a screwdriver.

2. Adjust the Tracks

The garage door track connects to the door frames via metal clips. The tracks are a guideway for garage door rollers. To adjust the garage door track, you will need to set it in correct alignment with the rollers.

The metal clips in the garage door tracks allow for adjustment from side to side. Usually, Metro Garage Door states that a binding garage door happens as a result of the tracks being too close to the door. Tap the lower end of the tracks with a rubber mallet to set it in proper alignment.

3. Tighten the Track Screws

After you have aligned the tracks in position, the next step is tightening the track screws so that the track doesn’t fall out of place again. Repeat the whole process for the different garage door tracks.

Rubbing/ Gaping Garage Door

There are countless reasons for a garage door that rubs against the molding. Fix the problem using the below steps:

1. Loosen the Track Bolts

Loosen the bolts that secure the tracks to the brackets.

2. Reset the Door Gap

Adjust the tracks to the left or right, so there is no gap between the door and the rubber molding. Aim to have half an inch and no more than three-quarter inches between the door and the track. Repeat the process with the tracks on the opposite side of the door.

3. Tighten the Bolts

Now that you have reset the tracks tighten the bolts, so the tracks don’t move position.
To adjust a garage door that binds, loosen the screws on the track, change the track position and tighten the screws back in place. To adjust a garage door that rubs against the molding, loosen the track bolts, adjust the gap between the tracks and the door and tighten the screws back in place.

Operating a garage door that isn’t working correctly comes with many risks. Typically, issues with garage door functionality have to do with the garage door tracks. Don’t know how to adjust garage door tracks? Follow the simple steps in this guide to know how to adjust these tracks in different situations.

Don’t know how to adjust garage door tracks? Garage doors usually open and close by rolling up and down, and the rollers on your garage door are guided by two tracks. These tracks run from the floor to the ceiling and on every side of the doorway, there’s an individual door track. Without a doubt, these tracks are designed to help the garage door operate smoothly, but when they are hit or have become loose, your garage door won’t operate as smoothly as it should. When the garage door track is out of alignment, it causes some issues but the most common ones include:

  • The garage door might bind which in turn makes it hard to open and close
  • The door might rub against the rubber molding
  • A gap might appear between the door and the rubber molding

If you realize any of the above problems and notice the misalignment of the track, you don’t have to panic or call an expert to fix it for you because you can easily realign it yourself like a pro. In most cases, it may be necessary to realign both tracks and because you’re reading this article, we will tell you simple steps on how to adjust garage door tracks.

How to adjust garage door tracks

Adjusting the Tracks for a Binding Garage Door

Step One: Loosening the Track Screws

If the garage door is secured in the tracks, loosen the screws with the help of a screwdriver which will bind the tracks in the garage door frame.

Step Two: Adjusting the Track Position

Using a rubber mallet, tap the bottom of the track so it is perfectly vertical. For maximum effectiveness, use a spirit level to confirm that the track is indeed back in vertical alignment.

Step Three: Tightening Track Screws

After confirming that the track is in the correct alignment, tighten the screws to ensure that the track can’t move.

Step Four: Adjusting Other Track

After adjusting one track, you’ll have to adjust the other track as well. Therefore, use a rubber mallet to tap the bottom of the track and ensure it’s perfectly straight. Then, tighten the screws.

With those simple four steps, you have excellently adjusted the tracks for a binding garage door. Many people would ask, how can I adjust the tracks for a garage stop rubbing against rubber molding or has a large gap appearing between the door and the molding? Interestingly, you can do this in the simple steps below:

Adjusting the Tracks for a Garage Stop Rubbing Against Molding

Step One: Loosening Track Bolts

First things first, you have to loosen the bolts that secure every track to its lower track bracket using a wrench. Before you proceed with the next steps, confirm the bolts on both tracks are loosened.

Step Two: Adjusting Door Gap

Move one of the tracks either left or right until you leave a gap of about ¼ inch between the stop molding and the gap. Remember that the gap should be uniform and to the opposite track, do the same and confirm the gap is uniform.

Step Three: Tightening Track Bolts

Last but not least, tighten the track bolts using a wrench. Confirm they are well tightened, but avoid over-tightening them.

Bottom Line

After following the above steps keenly, your garage door should be running freely without rubbing or binding and you’ll know how to adjust garage door tracks like a pro. If you realize that the garage door isn’t working properly, or should you suffer any complications when aligning the garage door track, don’t psych yourself out; consult a professional garage door maintenance provider to see if they offer services that will remedy the issue, and the problem will be history.

Request Service Today

We’ll fix your garage door problem fast! Call us before 1:00 PM and we’ll send an expert technician to fix your door on the same day. Call during our regular or extended service hours to talk to a customer service representative.

How to adjust garage door tracks

Guiding the door are the tracks on both sides of the garage door.

Without proper adjustment, the garage doors may not open or close properly.

If worse comes to worst, the door may come out of track causing damage to the tracks.

Adjusting the tracks correctly will prevent future problems with the garage door.

In this article, we will show you the ways on how to adjust garage door tracks.

Ways to Adjust the Tracks

Adjustment of the garage door tracks can be done in two ways.

For the rollers to work properly, one thing we can do is to align the track with the door itself.

Another way is to adjust the track in such a way that the door and the weatherstripping become aligned.

Adjusting Garage Door Track to the Rollers

The following are steps in adjusting the track to the rollers:

  1. First, work with garage door down.
  2. One at a time, loosen the tracks.
  3. Loosen the lag bolts. Those are the ones that hold the track to the jamb.
  4. Slide the bracket until the correct distance is achieved.
  5. Loosen one or more clips if needed.
  6. Position the track where it needs to be.
  7. Tighten the clips with the track in the right place.
  8. Ensure that the lag bolts connecting the frame and the clips are tight.

Adjusting the garage door track margins

To keep proper alignment of the track with the door itself, we will need to adjust the margins of the garage door.

We can establish the proper placement of the tracks when the door is down on the ground.

What we want is for the door and the tracks to be parallel.

Additionally, we want to achieve a consistent margin for the door’s full height.

The steps below will help guide in the proper adjustment of the garage door track margins:

  1. Using a wrench, loosen the bolt.
  2. Adjust the bracket in the desired direction. For binding brackets, we need to loosen two brackets at a time.
  3. Do adjustments to the brackets on both sides of the door until we come up with consistent margins of the garage door track.

Adjusting the Overhead Track

There is only one point for adjustment on the garage door track’s overhead portion.

The distance between the door and the overhead track must be equal to its distance from the wall track.

Again, adjusting the tracks requires working with the door down or closed.

Slots can be found in the brackets holding the track up.

Additional holes can also be found in them.

To perform the adjustment, we need to move the track.

Below are the steps in adjusting the overhead track:

  1. If using new holes is necessary, remove the bolts. Otherwise, just loosen them.
  2. Move the track’s end closer to the door or far away from it, whichever is necessary. Proper distance between the track and the door is vital. Making the track too far away from the door can cause falling of the door. Making the track very close to the door can cause binding of the door.
  3. Move the end of the track in small increments and try the door with each move until the desired adjustment is achieved.
  4. Tighten the bolts and check proper adjustment by operating the garage door.

Aligning the Garage Door Track with the Weatherstripping

Sometimes daylight and cold air come in the garage through the door tracks.

This means that we need to adjust the track to the weatherstripping.

Follow the steps below to perform the adjustment.

  1. Loosen the bolts.
  2. Move the track so that it fits snugly into the framing.
  3. Tighten the bolts back up.
  4. Check the alignment of the tracks together with operation of the door.

If everything is doing good, then we are done.

Otherwise, we repeat the steps.

Adjusting the garage door tracks may sound difficult.

But now that we have outlined the steps on how to adjust garage door tracks, we know that it is not that complicated.

If we are not confident enough to do the job by ourselves, it is always best to call the help of experienced garage door professionals.

How to adjust garage door tracks

Garage doors have tracks guiding the rollers up the ceiling and down the floor.

It is inevitable for these tracks to end up misaligned after using your garage door for quite some time.

Many factors can cause garage door track misalignment.

Maybe it is due to an accidental impact or other worn-out or corroded components.

If you notice that your garage door tracks are not in line and need an adjustment, better take necessary actions immediately.

A large gap between the garage door and its weather-stripping may also cause track misalignment.

When faced with this problem, it is essential that you know what to do.

If you’re in doubt and need some help, here’s how to adjust garage door tracks for your guide.

Steps to Adjust Garage Door Tracks

Garage door tracks can be simple yet complicated to align.

But here are some helpful steps you can follow for a proper track adjustment.

Loosen Screws and Bolts

When adjusting the tracks of a binding garage door, you need to loosen the screws first using a screwdriver.

Make sure to loosen the screws enough before taking the next step.

For a garage door with a gap problem on the bottom part, loosen the bolts that secure the tracks to its lower bracket with the use of a wrench.

Confirm if the bolts are loosened, and then proceed with the next action.

Adjust Track Position

Using a rubber mallet, adjust the track position carefully.

Do not use a hammer because it may damage your garage door tracks.

Exert optimal force to correct the position of your door track.

You may also opt to use a level tool to get the right position and prevent mistakes in the adjustments.

When adjusting door gaps, you can move one of the tracks on either side until there’s only about a quarter-inch left on the gap.

Remember to do the same thing with the opposite track and ensure that they have uniform gaps.

Tighten Screws and Bolts

After making the right adjustments, you can tighten the screws and bolts back to finish the job.

If necessary, take the steps again to adjust other garage door tracks.

Why You Need to Adjust Garage Door Tracks

Your garage door performs its opening and closing functions with the help of both the rollers and tracks.

The tracks provide a guide for the roller to run from the ceiling down to the floor.

There’s also an individual track on each side of the doorway.

These tracks help your garage door run smoothly.

That’s why when they get damaged or misaligned, your garage door may fail to operate as it should.

A misaligned garage door track can cause some issues which need an immediate solution to keep everything in place.

It is vital to make the necessary adjustments right away before something out of hand happens unexpectedly.

If you don’t know how to adjust garage door tracks, there’s no need to panic.

You can call an expert garage door repair technician to realign them for you.

Hire the Pros

Garage door track adjustments might not be for you.

Although the steps are quite simple, you may lack time to execute everything due to busy schedules and other engagements.

You may also don’t have the right tools for the job, and buying them might cost you a lot more than hiring professionals.

If you want to take the trouble off your hands, you can always choose to get help from a certified and trusted garage door repair company in your area.

Hiring a well-trained team is the best way to adjust your garage door tracks without having to exert much effort and waste time in the process.

Conclusion

Now that you know how to adjust garage door tracks, it will be much easier to fix future issues yourself.

Following the steps mentioned earlier should make your garage door move freely without any binding or chafing issue.

However, if you encounter further problems when adjusting the tracks, don’t leave it to yourself.

Consult the expert technicians of Marksman Garage Doors and get the best solution.

We will remedy your track issue and other garage door concerns.

Don’t let yourself suffer from the consequences of DIY track adjustments.

There is a garage door track on each side of the doorway. These tracks run from floor to ceiling and continue horizontally. They guide the rollers that the door runs on.

When the track is out of alignment, the door may bind or rub against the weatherstripping. Also, a gap may appear between the door and the weatherstripping.

How to adjust the track to the rollers

You need to set the track to the correct alignment for the rollers. First of all, find the metal clips securing the track to the framing. The slots that can be found on every clip are necessary for making side to side adjustment.

How to adjust garage door tracks

Typically, the distance between the edge of the door and the track is in between 0,5″ to 0,75″ (these figures are not strictly accurate for every situation). This distance allows the rollers to move in and out of the sleeves. Check that the door is neither too close nor too far from the track, because in these cases the door will bind or the rollers will pull out of the sleeves.

Attention!

Always lower the door before you start working. Never work while the door is up.

Also, it is important that you only loosen one track at a time and never remove the lag screws altogether. Just loosen the screw and slide the bracket to put it in the right position. It is very likely that you will have to work with several clips. Do not forget to tighten all the clips when you’ve set the correct alignment.

How to adjust the overhead track

Check out that the overhead part of the track and the wall track are at the same distance from the garage door. If you notice any difference, lower the door and start working. You need to relocate the end of the track so that it is parallel with the door, 0,5″ to 0,75″ away from it.

If you want to use an existing hole, just loosen the bolts. If you want to use a new hole, remove the bolts altogether. Now you can slightly draw the end of the track closer or away from the door. See if the operation of the door improves. If not, move the end of the track once more and tightly secure the screws. The rollers should neither bind nor pull away.

Attention!

Do not stand underneath the garage door! Do not start working until the door is down.

How to adjust the track to the weatherstripping

Close the door and check whether it is touching the weatherstripping. Do you spot the light or a draft? If yes, loosen the screws and move the track toward the framing. Tightly secure the screws and check whether the gap has disappeared. If you do not like the result, pay attention to the clips above or below: it is often necessary to adjust several clips.

How to adjust garage door tracksThis article covers adjusting a garage door track. When the track is out of adjustment it can cause the garage door to not operate correctly. In extreme cases the door can even come out of the track.

There are two ways that you can adjust garage door track. (1) You can align the track with the door itself, so that the rollers work properly. (2) You can adjust the track so that the door aligns with the weatherstripping.

Adjusting Garage Door Track to the Rollers

Adjusting the Track to the Rollers. The garage door track is attached to the door frame with metal clips. The track acts as a guide for the garaged door rollers. Adjusting a garage door track may involve setting the the track to the proper alignment for the rollers. See the article ‘Garage Door Rollers’, for more information on the correct alignment.

The clips have slots in them that allow for side to side adjustment. Rule of thumb, you should have about 1/2″ to 3/4″ between the edge of the door and the track. This leaves some room for the rollers to move in and out of the sleeves. When the track is too close to the door, the door will bind. Too far away and the rollers could pull out of the sleeves.

Safety First!!

When you are adjusting garage door track, you want the door down. Only loosen one track at a time and do not remove the lag bolts completely. Loosen the lag bolts that hold the track to the jamb and slide the bracket until the distance is correct. You may have to loosen more than one of the clips. Get the track where you want it and tighten the clips back down. Make sure the lag bolts that attach the clips to the framing are tight.

How to adjust garage door tracks

Adjusting the garage door track margins keeps the track properly aligned with the door itself. When it is resting on the ground the door establishes where the tracks should be. You want the tracks to be parallel with the door and have a consistent margin for the full height of the door.

Adjusting the margins along the side of the door is similar to adjusting it in and out. The brackets are fastened to the jamb with lag bolts. The hole in the bracket is also slotted. This allows the bracket to move from side to side the length of the slot. Hopefully, the installer put the lag in the center of the slot.

You will need a wrench to loosen the lag bolt. Loosen the bolt and adjust the bracket in the desired direction. You may need to loosen two brackets at a time if they are binding.

Adjust the brackets on both sides of the door until you have a consistent garage door track margins. You should be able to see about 1/2″ to 3/4″ of the shaft.

Adjusting the Overhead Track

How to adjust garage door tracksThe overhead portion of the garage door track only has one adjustment point. The overhead track should be the same distance away from the door as the wall track. Do not try to adjust the track with the door up. The brackets that hold up the track have slots and additional holes in them. The end of the track will need to be moved to to adjust it.

Loosen the bolts or remove them if a new hole needs to be used. Move the end of the track closer or away from the door as needed. Do not move it very far each time. If the track is too far away from the door, the door could fall. Too close and the door will bind. Move the end of the track the minimum increment and try the door. You want the track to be parallel with the door, 1/2″ to 3/4″ away from the door. Tighten the bolts as needed and carefully try the operation of the door. Do not stand underneath it and watch carefully for binding or pulling away of the rollers.

How to adjust garage door tracks

Adjusting overhead garage door track is similar to adjusting the tracks along the side of the door. The difference is that the track only has one place that you can adjust it at. Assuming that the overhead garage door track is not bent, this will work fine.

The ends of the garage door tracks are usually held in place by metal angles that are attached to the ceiling or rafters. The metal angles have holes in them, some are slotted and some are not. The idea is to have the track parallel to the door in its up position.

You want the rollers to show about 1/2″ to 3/4″ margin on them. Raise the door and check the alignment. Note which way the track needs to move and how much.

WARNING. Do not work on the overhead tracks with the door in the up position! WARNING.

To adjust the track you will need to move the vertical angle in the proper direction. Remove the bolt from the angle and move the angle over one or more holes to get the desired margin. You can use wrenches to loosen the bolts. Do one track at a time with the door in the down position. Raise the door carefully the first time to make sure that the rollers will not pull out of the sleeves.

WARNING!! DO NOT Try to Adjust the Door When It Is Up. Lower the Door Before You Work On It!

Adjusting Garage Door Track to the Weatherstripping

Often, you will need to adjust the track to the weatherstripping. For all but the top clip, there are slotted bolt holes where the track is attached to the clip. With the door closed the door should be touching the weatherstripping. Do you see daylight or feel cold air coming in? You can loosen the bolts and move the track toward the framing. Snug, but not too tight. Tighten the bolts back up and check the operation of the door.

It is possible that you will have to adjust more than one of the clips. Do not force the track. If it won’t move the proper distance, loosen the clips above or below it. Get the full length of the track adjusted so that the door is snug against the weatherstrip (no daylight, right?). Tighten the bolts up and you’re done. Adjusting garage door track did not turn out to be that tough. Good Job!

For more information on ‘Garage Door Weatherstripping’, follow this link.

Summary

So you can see that there are several adjustments on a garage door that involve the track. Fortunately, most of the time it is not that difficult to make these adjustments. Hopefully your door is operating better now.

How to adjust garage door tracks

There’s so much that goes on behind the functioning of a garage door that most garage owners have likely overlooked.

When problems arise hence, a considerable chunk of their time is spent on trying to locate the source of the problem.

Therefore, one must be thoroughly acquainted with the workings of one’s garage door to save them from an ordeal such as taxing as that.

Garage door tracks, in this respect, are most frequented with the concern of being too loose or tight.

Given that garage doors, in general, are subjected to high and intense pressure almost every day, it is not a rare occurrence for these massive doors to suffer through bouts of complications.

Garage door tracks are built to ensure that garage doors operate smoothly.

They are responsible for the rolling motions that help the doors open and close and are usually situated from the ground to the ceiling, extending on every side of the doorway.

Should these tracks misalign, it could cause a horde of other problems.

When this happens, the most enticing prospect would be to call for a professional; however, others would rather have it fixed by themselves to save them from squandering money.

As such, this list seeks to present several pointers on how to adjust garage door tracks.

Loosen the screws of the tracks.

The first step in fixing the adjustment of the garage door tracks is to loosen first the screws that are fastening the garage door tracks together.

Make use of a screwdriver to do such.

This will bind the tracks to the frame of the garage door.

Adjust the position of the tracks.

Make sure that you are equipped with a rubber mallet for it.

Make use of the mallet and rap the lowermost part of the track until it is perfectly vertical in its alignment. In order to ensure the effectiveness of such a method, utilize a spirit level in order to confirm that the track is now in its proper vertical position.

Tighten the screws of the tracks.

Once you have done the steps above, the next thing to do is to fasten the screws that were previously loosened.

If you have ascertained that the tracks are now in their vertical alignment, tighten the screws once again.

This is to make sure that the tracks do not move again.

Adjust the remaining tracks.

After the successful adjustment of the first track, repeat the same steps again on the other remaining tracks.

Why you need to leave it to the experts

At first, glance, adjusting the tracks may be easy.

However, without the proper training and equipment, it would not work for just any person.

For one, even if you have the right equipment, it does not equate to having the right knowledge in using them.

A rubber mallet may be difficult to handle for some.

It takes years of experience to have a license as well as training to be able to practice in the field of garage door repair.

As such, it is not easy to solve a garage door problem on your own.

For people who do not have the time, it is better to hire a worker to do it.

For people who do have the time but do not know how to work their way around the mechanism, hiring a professional is the best choice.

It does not help to waste time trying to repair something blindly.

For best results, it is recommended that you hire an expert to take a look at your garage door.

With that in mind, leave it to us! Our services guarantee that your garage door will be on track in no time.

We take pride in our ability to provide quality and great results in all the garage door services we provide.

We are licensed as well as insured.

Not only that, but our professionals also boast experience and expertise in the field.

As such, we have been proven and tested by previous customers who have given us great ratings.

Given that, there is no reason for you to doubt! Call us now for the well-being of your garage door.

Over the years, modern society has seen a spike in state-of-the-art amenities.

A great turn of affairs, many would think; technology in all its noble splendor.

Be that as it may, some continue to stick faithfully to what they have always been accustomed to.

One instance could be opting to brew one’s coffee on a grinder manually instead of having it served pronto by a coffee maker that could operate as if it were a barista at some coffee shop – this among many.

While it is true that society has amiably welcomed the advantages of technology, there are still those who would instead remain in the comfort of a familiar pattern.

Garage doors, for this matter, are no strangers to modification.

Along with countless innovations, augmentations, and revisions, these doors have evolved into types of home fixtures that homeowners could rely on.

Some of these door types have been enhanced to appease modern living trends, while others impart a sense of belongingness with the past fads.

Considering that these huge doors are subject to constant tension, it’s only natural for its tracks to come loose.

This list, therefore, serves to provide pointers on how to adjust garage door tracks.

Unfasten the tracks

The first step to a project is to simply remove everything and start over.

This ensures that the project goes well without any interference and hassle with the objects that need no fixing.

For the garage tracks, as there are a number of screws fastened around it, we need to loosen it first.

These screws are the ones that are responsible for the fastening of the garage door frame, so they do not unhinge during the operation.

As such, when looking to adjust the tracks, unfastening these screws should be the first step.

Make sure that these screws are unfastened enough before doing anything to adjust the tracks.

Fine-tune the garage door tracks

With a garage door track that is out of adjustment, fine-tuning is just what it needs.

First, get a rubber mallet.

This is the tool that we will be used to adjust the tracks.

If you are thinking of swapping it up for a hammer, think again.

A hammer can easily damage the tracks of the garage door, so it should be avoided.

You can then proceed with the adjustment by making use of the mallet.

On the foot of the door track, use the rubber mallet and swing it with force in order to correct the position.

A level tool can also be utilized so as to ensure that the tracks stay in place and in an accurate position.

Tighten the tracks

After the adjustment and repositioning of the tracks have been done, putting the screws back to where they belong in the final step.

Tighten the garage door‘s screws, and that is basically everything.

For the other tracks, simply repeat the previous steps.

However, if you are not sure if you can do a good job in doing such a project, it is best to leave it to the professionals.

One small wrong swing of the mallet can cause more damage that can require an even bigger fix.

As such, as a homeowner, carefully evaluate the risks and your ability to be able to perform such a repair.

Look out for further problems

A garage door that is out of alignment or adjustment is not a simple issue.

It is not just a matter of misadjustment.

For the most part, it might be due to an even bigger issue, which can lead to a whole lot of damage and fixing.

As such, if you notice your door being out of place, act on it immediately and fix it before it causes any more damage.

As they say, prevention is the best cure.

When you notice something is off, have it fixed immediately.

Trust Austin’s Garage for all your garage door issues

In how to adjust garage door tracks, it is best to leave to people who know the way around it.

With that said, Austin’s Garage is composed of experienced experts who are trained professionals at handling garage door issues.

As a company that has been proven and tested by numerous clients, we assure you that our services are of quality.

Call us, and we’ll prove it to you! Contact us today.

How to adjust garage door tracks

When track issues occur, your garage door will not function efficiently.

Misaligned or damaged door tracks may cause the rollers to wear out quickly.

It may also cause the door to rub or bind against the rubber molding.

In worst cases, faulty tracks may cut through the garage door spring cables and cause the entire system to break down.

For that, it is essential to make necessary track adjustments when there’s a problem.

Here’s how to adjust garage door tracks for a helpful guide.

You can also view this video for further understanding.

Causes of Garage Door Track Misalignment

Using a garage door with misaligned tracks is a risk not worth taking.

You may experience getting locked inside or outside your garage.

What’s worse is that an uneven garage door can suddenly snap off the tracks, causing damages and injuries.

Broken garage door tracks also create a security risk.

Since the door won’t close properly, it makes your home or business more vulnerable to break-ins.

But you may wonder what’s causing the misalignment in your garage door tracks.

Many factors can make your garage door tracks go out of place.

It may be because it’s old or the rubber molding has worn out.

Also, the garage door may become loose due to constant usage.

Whatever the reason is, you must understand how to adjust garage door tracks.

Knowing such things will help you take the right action when problems occur.

Follow these steps to get your garage door back on track.

Fixing Issues on Binding Garage Doors

A binding garage door is difficult to lift and takedown.

There are various possible reasons why this happens, and these are the ways you can take to solve the problem:

Loosen the Screws

If your garage door is hard to move, try to loosen the track screws.

They may be too tight, which causes your garage door to bind.

Lift your garage door to locate the bolts on the track brackets.

Use a screwdriver to loosen the bolts.

Change Track Alignment

The metal clips connect the door frames to your garage door tracks.

These tracks guide the garage door rollers.

During adjustment, you have to set the tracks in proper alignment with the rollers.

With the metal clips, you can make necessary adjustments from side to side.

In most cases, a binding garage door occurs due to the tracks being too close to the door.

You can tap the bottom end of the garage door tracks using a rubber mallet to get the proper alignment.

Tighten the Screws

Once the tracks have aligned, you can tighten back the screws to secure your garage door.

Repeat this process for the other garage door tracks.

Resolving a Garage Door Gap

Fix your problem with the garage door gap by following these steps:

Loosen the Bolts

Loosen the garage door bolts that bind the tracks to the brackets.

Adjust the Door Gap

Make adjustments on the tracks to eliminate or lessen the gap between your garage door and the rubber molding.

Aim for a half an inch and three-quarters inches’ distance between the track and the door.

Do the same for the other garage door tracks.

Tighten the Bolts

After resetting the tracks and gaps, tighten the bolts back to secure the tracks in position.

Conclusion

Operating a garage door with misaligned tracks comes with risks.

Garage door functionality issues often involve the track as it’s a crucial system component.

To adjust a binding garage door, loosen the track screws, realign the track, and tighten the screws back.

On the other hand, to fix a garage door gap, loosen the bolts, adjust the gap, and tighten the bolts to secure the tracks.

If the job gets too tough and you need a garage door repair in Cleveland, we’re ready to back you up.

You don’t need to prepare the tools and carry out the risky job yourself as we have professionals for garage-door-related concerns.