Categories
Home-and-Garden

How to adjust a mesh watch strap

Our crafted mesh straps are the perfect finishing touch to any outfit. They are delicate, soft and lightweight, with a convenient length adjustment mechanism. To adjust your mesh strap, please follow the step by step instructions below.

How to adjust a mesh watch strap

STEP 1: Lift the Clasp

Insert a small flathead screwdriver or similar tool into the inner slot, and pry the locking clip up and release the clasp from the strap

STEP 2: Slide the Clasp

Slide the clasp up or down to your preferred position, align the indentation on the back of the clasp with a groove in the mesh strap

STEP 3: Secure the Clasp

Use the leverage of the screwdriver to press down the clip and lock the clasp into place

*Be careful not to damage the clip by using too much force or aligning it in such a way that it is not firmly seated in a groove in the mesh.

Pay Attention to the Grooves in the Mesh Strap:

(Align slider to engraved level)

There are some grooves in the back side of the mesh strap aligned with the indentation on the back of the clasp to lock the clasp.
If indentation on the back of the clasp is not aligned with the grooves in the mesh strap, please release the clasp and then adjust it according to above steps.

Mesh watch straps have a unique look that many find appealing. However, while you may know how to open a mesh watch band, do you know how to adjust it to get the perfect fit? Knowing how to adjust watch clasp on a mesh strap is essential if you are buying a new watch, as they tend to be set for the larger wrist from the factory, so what do you do if you need to adjust mesh watch band size yourself?

How to adjust a mesh watch strap

Getting the tools together

It is fairly easy once you know how to adjust mesh watch band sizes, but you do need a few tools to be able to do it at home. These are:

Spring bar tool

Jeweler's small ball-peen hammer

The other thing you need is the measurement, where you need the mesh strap adjusted to. For this, a sharpie is ideal, simply wrap the strap around your wrist and mark where the clasp should be. That is all you need for preparation, now its time to get the mesh strap adjusted.

How to adjust mesh watch strap

Lay the mesh strap on a flat surface so you are looking at the inside of the sliding part of the watch clasp. You will see a small metal part that clamps down on the strap to keep it in place. It is held in place by spring pressure, using your spring bar tool you can lift this clamp up and release the tension, freeing the strap and allowing the clasp to be slid to the desired position easily.

Once the clasp is in position at the mark you previously made, use your pin pusher to reseat the clamp back against the mesh strap. In most cases, this can be done just using finger pressure, but if the clasp is especially stiff, use your hammer to gently tap it back into place.

Try the mesh watch band on, and check it is adjusted correctly. It really is that simple!

How to adjust a mesh watch strap

Some say it takes lots of experience to adjust these bracelets. The truth is that a mesh bracelet is actually much easier to adjust than a link style bracelet, and you can even do it yourself.

All you need is a appropriate tool and follow the steps below:

  • A jeweler’s small ball-peen hammer
  • A pin pusher
  • And a spring bar tool

How to adjust a mesh watch strap

Step 1
When you need to adjust the length of your metal watch band, it helps to know exactly how much shorter the band needs to be. You can do this by wrapping the band around your wrist and marking where the clasp should sit if it fit your wrist the way you wanted.

How to adjust a mesh watch strap

Step 2
Then, take your watch band and lay it out flat on your work surface so that you can see the inside of the bottom portion of sliding style watch band clasp. Look inside the clasp where the mesh band slips through it. You will see a small metal strap that crosses over the metal band under the hook where the clasp closes securely. This is what keeps the clasp in place on the band.

Step 3
Take your spring bar tool and insert the forked end under the metal strap between the band and the clasp. Gently pry the metal strap up until it opens enough for you to slide the clasp up or down the watch band.

How to adjust a mesh watch strap

Step 4
Position the clasp closer to the watch movement end of the mesh band where you need it to sit for it to fit your wrist comfortably.

Step 5
Once the clasp is sitting where you think it should, take your pin punch and press it down on the metal strap. The metal strap may click into place, just with the force of your hand, if it doesn’t, take your ball peen hammer and gently tap it into place.

How to adjust a mesh watch strap

Step 6
Set your tools aside when the strap is securely holding the mesh band again. Try your watch band on.

Finished
Once the band is put back together again, try on the watch band. It should fit just the way you like.
If the band is still too big, or maybe too small now, start over by repeating what you did before to open the metal strap and reposition the clasp on the band.

Related Posts

How to adjust a mesh watch strap

  • How to adjust a mesh watch strapHow to adjust a mesh watch strap
  • How to adjust a mesh watch strapHow to adjust a mesh watch strap
  • How to adjust a mesh watch strapHow to adjust a mesh watch strap
  • How to adjust a mesh watch strapHow to adjust a mesh watch strap
  • How to adjust a mesh watch strapHow to adjust a mesh watch strap

We can custom the watches as your design if you can’t find interested models here. Contact us today!

Our customer-specific solutions are tailored to fit your exact business needs.

One of the largest selections of Public Guidance products in the industry – all in one place.

Selecting the models and quantity you need and transfer them to the form below the products, the PI will update to your inbox quickly.

Our global sourcing ensures that we can always offer the most competitive pricing, and our bi-coastal shipping saves you even more on freight.

In this guide, we will demonstrate how to adjust the length of our mesh strap with clasp, such as the thin mesh strap and the older version of the mesh band for Fitbit Inspire . We recommend using a spring bar tool for this process, however you may also use a small screwdriver or other small prying tool that you may already have on hand.

STEP (1): Begin by releasing the outer latch, which can be done by using your thumbnail to pry it open, as shown below.

How to adjust a mesh watch strap

STEP (2): Lift the outer latch away from the strap, and unhook it from the clasp so that the inner latch is exposed.

How to adjust a mesh watch strap

STEP (3): Next, release the inner latch. To do so, use the spring bar tool (or other small prying tool) to pry open the latch, as shown in the animation below.

STEP (4): Once the inner latch has been released, you can freely slide the clasp up or down along the strap to adjust the length, as needed.

How to adjust a mesh watch strap

STEP (5): Once the clasp has been adjusted appropriately, close the inner latch by pressing down on it firmly with your thumb.

How to adjust a mesh watch strap

STEP (6): Make sure that the inner latch has been closed securely.

How to adjust a mesh watch strap

STEP (7): Reattach the outer latch by hooking it back onto the clasp. To do this, reverse the process from STEP (1) and (2).

How to adjust a mesh watch strap

1 Comment

John August 12, 2021 – 15:22

Great instructions … easy. This was the one step that I couldn’t figure out on my own.

How to adjust a mesh watch strap

When you need to adjust the length of your metal watch band, it helps to know exactly how much shorter the band needs to be. You can do this by wrapping the band around your wrist and marking where the clasp should sit if it fit your wrist the way you wanted.

Step 2

Then, take your watch band and lay it out flat on your work surface so that you can see the inside of the bottom portion of sliding style watch band clasp. Look inside the clasp where the mesh band slips through it. You will see a small metal strap that crosses over the metal band under the hook where the clasp closes securely. This is what keeps the clasp in place on the band.

How to adjust a mesh watch strapStep 3

Take your spring bar tool and insert the forked end under the metal strap between the band and the clasp. Gently pry the metal strap up until it opens enough for you to slide the clasp up or down the watch band.

Step 4

Position the clasp closer to the watch movement end of the mesh band where you need it to sit for it to fit your wrist comfortably.

How to adjust a mesh watch strapStep 5

Once the clasp is sitting where you think it should, take your pin punch and press it down on the metal strap. The metal strap may click into place, just with the force of your hand, if it doesn’t, take your ball peen hammer and gently tap it into place.

Step 6

Set your tools aside when the strap is securely holding the mesh band again. Try your watch band on.

If the band is still too big, or maybe too small now, start over by repeating what you did before to open the metal strap and reposition the clasp on the band.

Finished

Once the band is put back together again, try on the watch band. It should fit just the way you like. Now that you have completed one repair, you can learn more about simple watch repair at our Learning Center .

How to adjust a mesh watch strap

Hey, are you upset that your mesh watch band is that not fitting you properly?

And you’re just wondering how to adjust the mesh watch band?

We can understand what do you feel right now.

Don’t worry dear.

We can help you to know how to adjust your mesh watch band properly.

Adjusting your mesh watch band is not much complicated. Just pay proper concentration during the entire procedure.

This article will discuss the mesh watch band and its adjustment to give you a clear idea of it.

Let’s start from the beginning…….

Look, everyone knows that watches band compiled of traditional leather or metal strap, right?

Then why the band of the mesh watch is different from operating?

Always remember that a good mesh watch band has a good consistency and durable mesh.

You will see that the strap of this watch is very flexible and lacks sharp edges.

Moreover, the mesh watch band is able to envelop your wrist very softly that you’ll like to use it on a regular basis.

If you notice after purchasing that your mesh watch band is much larger, please don’t panic.

Simply remove links from the band to make it smaller and make sure that it fits your wrist properly.

Did you get the small flathead screwdriver?

If no, then get it before you start adjusting your mesh watch strap.

Using the flathead screwdriver, you can easily adjust your mesh watch band.

To fit your mesh strap around your wrist comfortably, you need to adjust the sliding clasp’s placement in the right portion.

For simplicity, now we’ll discuss the whole procedure step by step so that you don’t get any complication to adjust your mesh watch band further.

Get A Small Flathead Screwdriver for Your Mesh Band

How to adjust a mesh watch strap

To open the clasp, you must need a pointed object with a tiny sized flathead screwdriver. With this screwdriver, you can pry to open your mesh clasp.

It is highly recommended to you to use that screwdriver that also use to adjust eyeglass screws.

An enlarged screwdriver must not work well since it would be much larger to fit into the clasp.

What if you have no small screwdriver?

The answer is you can use a small blunt tool.

Please note that do not use a knife blade.

The knife blade could slip, and the sharper front point can cause scratch your watch.

Moreover, you can also cut your fingers with a knife. Therefore, do not apply the knife blade.

Hold the clasp of your mesh watch band steadily

In this step, you should take your mesh watch band on a table or a firm surface.

Now, you will see the inside part of your watch clasp strap. Right?

If yes, look at the bottom portion of your watch band clasp to detect the exact location from where your mesh strap slips through it.

There is also a metal strap under the hook of your watch band.

With this hook, you’ll be able to close the clasp of your mesh watch strap securely.

Remember, use your non-dominant hand to hold the clasp of your watch in the right state firmly.

If there is no table near you, it is also possible to hold your mesh watch strap in your hand.

But we do not suggest you do so if you have no previous experience in it.

To make it done efficiently, you should do this process on a table.

Use screwdriver head into the small hole on the mesh band’s clasp

After layout your watch band clasp, you will see that the front side of your clasp.

If yes, you will get a small hole around 0.64m in width directly to its center.

Now take your screwdriver or a blunt tool, which you have directly into the hole. Then, use that small hole to pry the band open.

Please note that mesh watch has different brands. Therefore, the type and length are also varying from brand to brand.

That is why your watch clasp’s hole would be different in shape and size you are adjusting.

In addition, there is also some type of clasps of mesh band which have a small arrow pointing directly to the hole.

Pray your mesh band clasp upwards to open

When you pray the clasp of your mesh watch band upwards to open, you can see that there is a small set of grips at the base of your watch clasp. It’s nearly close to the watch’s face.

We prescribe you to slowly pressure the screwdriver to open the clasp of your mesh watch.

What if the clasp doesn’t open fully with a screwdriver?

Many people get this issue while they want to do so. If you also face this situation, use your thumb and index finger to open it entirely.

How to adjust a mesh watch strap

Adjust the clasp of your mesh watch

Now it’s time to adjust your clasp according to your wrist. If you slide the clasp of your watch farther up, it will tighten your watch’s band.

On the contrary, if you slide the clasp down, your watch’s band will lose the strap.

Align your mesh watch’s clasp with a groove

Depending on the design of the mesh watchband, it will have a small groove around 0.30 cm.

If you take a look at the back part of the clasp, you will see there is the same indentation that fits into any of these grooves nicely.

You cannot close the clasp properly if you do not align it with a slot subsequently in the mesh band.

How to adjust a mesh watch strap

Close the clasp of your mesh watch’s band

When you align it properly with a groove in your mesh watch band, you will get the best position for your mesh band.

After getting the right position, simply close your watch’s clasp to lock it in its place.

You will get a sound while you shut the clasp rightly. At this point, your mesh watch band is ready to use.

How to adjust a mesh watch strap

Final Recommendation

Follow the whole procedure step by step as we have discussed.

We’ve tried our best dear reader, to make you understand to do it yourself with no complication.

Remember, do you drop the clasp on the floor during the procedure. Otherwise, your work will go in vain.

Let us know what do you think now after reading this article?

Share your experience regarding the adjustment of your mesh watch band.

We would love to hear from you, dear.

If you think we could help you out, please share this article with your friends and family.

1. You will find a small flathead screw driver in your Nominal watch box.

How to adjust a mesh watch strap

2. Hold the clasp steady. Place the watch flat on a table or other firm surface. Use your non-dominant hand to hold the clasp firmly in position.

  • If you’re not near a table, it’s possible to adjust the clasp if you’re holding the watch in your hand. However, if this is your first time adjusting a mesh watch strap, doing it on a table will make the process easier.

How to adjust a mesh watch strap

3. Place the screwdriver head into the small hole on the clasp. The front side of the clasp (which will be facing up when the watch is laying face-up) will have a small hole about 1 ⁄4 inch (0.64 cm) wide directly in its center. You’ll use this hole to pry the strap open. Put the tip of your screwdriver—or other tool—directly into the hole.

  • The hole will be shaped and sized differently depending on the brand of mesh strap you’re adjusting.
  • Some clasps may even have a small arrow pointing to the hole.

How to adjust a mesh watch strap

4. Pry the clasp upwards to open it. There will be a small set of hinges at the base of the watch clasp, on the side closest to the watch’s face. Slowly exert pressure down on the screwdriver to pry the top portion of the clasp up and open.

  • If the clasp doesn’t fully open with the use of the screwdriver, use your thumb and index finger to open it completely.

How to adjust a mesh watch strap

1. Slide the clasp up or down the mesh strap. Adjust the clasp to accommodate your wrist. Sliding the clasp farther up the mesh strap (towards the watch) will tighten the strap on your wrist, and sliding the clasp down the mesh strap (away from the watch) will loosen the strap.

  • Be careful not to drop the clasp on the floor.

How to adjust a mesh watch strap

2. Align the back of the clasp with a groove in the mesh watch strap. Due to its design, the back of the mesh watch strap will have a small groove every 1 ⁄8 in (0.32 cm) or so. The back of the clasp will have a corresponding indentation that fits snugly into any of these grooves.

  • If you try to close the clasp without first having aligned it with a slot in the mesh strap, the clasp will be unable to close.

How to adjust a mesh watch strap

3. Close the clasp. Once you’ve found the best position for the watch strap and aligned it with a groove in the mesh strap, close the clasp to lock it in place. [8] You should hear a “pop” sound as the clasp snaps shut.

1. You will find a small flathead screw driver in your Nominal watch box.

How to adjust a mesh watch strap

2. Hold the clasp steady. Place the watch flat on a table or other firm surface. Use your non-dominant hand to hold the clasp firmly in position.

  • If you’re not near a table, it’s possible to adjust the clasp if you’re holding the watch in your hand. However, if this is your first time adjusting a mesh watch strap, doing it on a table will make the process easier.

How to adjust a mesh watch strap

3. Place the screwdriver head into the small hole on the clasp. The front side of the clasp (which will be facing up when the watch is laying face-up) will have a small hole about 1 ⁄4 inch (0.64 cm) wide directly in its center. You’ll use this hole to pry the strap open. Put the tip of your screwdriver—or other tool—directly into the hole.

  • The hole will be shaped and sized differently depending on the brand of mesh strap you’re adjusting.
  • Some clasps may even have a small arrow pointing to the hole.

How to adjust a mesh watch strap

4. Pry the clasp upwards to open it. There will be a small set of hinges at the base of the watch clasp, on the side closest to the watch’s face. Slowly exert pressure down on the screwdriver to pry the top portion of the clasp up and open.

  • If the clasp doesn’t fully open with the use of the screwdriver, use your thumb and index finger to open it completely.

How to adjust a mesh watch strap

1. Slide the clasp up or down the mesh strap. Adjust the clasp to accommodate your wrist. Sliding the clasp farther up the mesh strap (towards the watch) will tighten the strap on your wrist, and sliding the clasp down the mesh strap (away from the watch) will loosen the strap.

  • Be careful not to drop the clasp on the floor.

How to adjust a mesh watch strap

2. Align the back of the clasp with a groove in the mesh watch strap. Due to its design, the back of the mesh watch strap will have a small groove every 1 ⁄8 in (0.32 cm) or so. The back of the clasp will have a corresponding indentation that fits snugly into any of these grooves.

  • If you try to close the clasp without first having aligned it with a slot in the mesh strap, the clasp will be unable to close.

How to adjust a mesh watch strap

3. Close the clasp. Once you’ve found the best position for the watch strap and aligned it with a groove in the mesh strap, close the clasp to lock it in place. [8] You should hear a “pop” sound as the clasp snaps shut.

Use the flathead screwdriver we sent you. You will need a small, pointed object to pry open the mesh clasp. The type of screwdriver used to adjust eyeglass screws would work well. A Phillips head screwdriver will not work, since it will be too large to fit into the clasp.

  • If you do not have a small screwdriver, you could use a different small, blunt tool. For example, try one of the prying tools built into a Swiss Army knife.
  • Do not use a knife blade. The point of the knife could slip and scratch the watch, or you could accidentally cut your fingers with the blade.

Hold the clasp steady. Place the watch flat on a table or other firm surface. Use your non-dominant hand to hold the clasp firmly in position.

  • If you’re not near a table, it’s possible to adjust the clasp if you’re holding the watch in your hand. However, if this is your first time adjusting a mesh watch strap, doing it on a table will make the process easier.

Place the screwdriver head into the small hole on the clasp. The front side of the clasp (which will be facing up when the watch is laying face-up) will have a small hole about 1 ⁄4 inch (0.64 cm) wide directly in its center. You’ll use this hole to pry the strap open. Put the tip of your screwdriver—or other tool—directly into the hole.

  • The hole will be shaped and sized differently depending on the brand of mesh strap you’re adjusting.
  • Some clasps may even have a small arrow pointing to the hole.

Pry the clasp upwards to open it. There will be a small set of hinges at the base of the watch clasp, on the side closest to the watch’s face. Slowly exert pressure down on the screwdriver to pry the top portion of the clasp up and open. [5]

  • If the clasp doesn’t fully open with the use of the screwdriver, use your thumb and index finger to open it completely.

Slide the clasp up or down the mesh strap. Adjust the clasp to accommodate your wrist. Sliding the clasp farther up the mesh strap (towards the watch) will tighten the strap on your wrist, and sliding the clasp down the mesh strap (away from the watch) will loosen the strap.

  • Be careful not to drop the clasp on the floor.

Align the back of the clasp with a groove in the mesh watch strap. Due to its design, the back of the mesh watch strap will have a small groove every 1 ⁄8 in (0.32 cm) or so. The back of the clasp will have a corresponding indentation that fits snugly into any of these grooves.

  • If you try to close the clasp without first having aligned it with a slot in the mesh strap, the clasp will be unable to close.

Close the clasp. Once you’ve found the best position for the watch strap and aligned it with a groove in the mesh strap, close the clasp to lock it in place. You should hear a “pop” sound as the clasp snaps shut.